Structural calculations to CSA and NBCC, every step shown with its clause.

Type a value and every step recomputes: the formula in symbols, the numbers substituted, the result with its unit, and the check it governs.

Browse calcs Sample report sheets

Animation of the bolt capacity calc: the edge distance is typed from 30 mm to 40 mm and back, and each time the drawing, the gross shear area step and the verdict update in turn, between FAIL at 30 mm and PASS at 40 mm. While it reads FAIL, every place the edge distance appears is highlighted.

A calc marked Verified lists each formula and clause with the code text behind it, or the definition, statics or table it rests on (how a calc is validated). Its PDF report is a typeset calc sheet with a title block for the project file (sample sheets).

Concrete

  1. RC bracket and corbel Pro report

    Strut-and-tie design of a reinforced concrete bracket or corbel to CSA A23.3-24.

  2. Concrete shear friction

    Interface shear transfer by shear friction, to CSA A23.3.

  3. RC beam shear and torsion Pro report

    Combined shear and torsion design of a reinforced concrete beam, CSA A23.3-24 Cl. 11.

  4. Tension development length and lap splice

    Development length and Class A and B lap splice length of a straight reinforcing bar in tension, to CSA A23.3-24 Cl. 12.2 and 12.15.

  5. Compression development length

    Development length of a reinforcing bar in compression, to CSA A23.3-24 Cl. 12.3.

  6. Standard hook development length

    Development length of a standard hook in tension, to CSA A23.3-24 Cl. 12.5.

  7. Strip footing capacity Pro report

    Bearing, one-way shear and flexure of a concrete strip footing to CSA A23.3.

  8. Pad footing capacity Pro report

    Bearing, punching, one-way shear and flexure of a concrete pad footing to CSA A23.3.

  9. Cantilever retaining wall Pro report

    Stability to CFEM and the stem, toe and heel to CSA A23.3, with surcharge, backslope, passive toe, key and a Mononobe-Okabe case.

  10. Compression development length (A23.3-19)

    Development length of a reinforcing bar in compression, to CSA A23.3-19 Cl. 12.3.

  11. Tension development length and lap splice (A23.3-19)

    Development length and Class A and B lap splice length of a straight reinforcing bar in tension, to CSA A23.3-19 Cl. 12.2 and 12.15.

  12. Standard hook development length (A23.3-19)

    Development length of a standard hook in tension, to CSA A23.3-19 Cl. 12.5.

Loads

  1. Seismic loads, rectangular tank Pro report

    Seismic design forces and overturning moments for a rectangular liquid-containing tank.

  2. NBCC load combinations

    Factored load combinations to NBCC 2020, with the governing maximum and minimum.

  3. Snow drift on a lower roof Pro report

    Drift beside a roof projection, or below a higher roof across a gap, to NBC 2020.

Masonry

  1. Masonry lintel Pro report

    Reinforced block or brick lintel: arching, load dispersion, flexure, shear and end bearing.

Steel

  1. Bolt capacity

    Factored shear and tensile resistance of a structural bolt to CSA S16-19.

  2. Weld capacity

    Factored shear resistance of a fillet weld to CSA S16 Cl. 13.13.

  3. Bolt prying action Pro report

    Prying action on a bolted tee or angle flange: flange, connection, bolt and web checks.

  4. Steel web shear capacity

    Shear stress capacity of an unstiffened steel web of a flexural member with two flanges, to CSA S16 Cl. 13.4.1.1.

  5. Connection transfer force

    Axial force and shear on a braced beam-to-column connection, by the uniform force method.

  6. Single angle in compression

    An equal-leg angle brace, concentric or bolted through one leg, to CSA S16.

  7. Axial compression of a WT, channel or angle

    Class 4 effective area and flexural-torsional buckling of a WT, C, MC or single angle.

  8. Axial compression of a W section or HSS

    Class 4 effective area and the least of flexural and torsional buckling, W shape or HSS.

  9. WT in compression and bending Pro report

    A WT brace with its stem in tension: compressive and flexural resistance and S16's interaction.

  10. Beam-column Pro report

    Axial compression and biaxial bending of a W shape, HSS or channel to CSA S16 Cl. 13.8.

  11. Concentrated load on a beam web Pro report

    Web yielding, crippling and sidesway buckling of a W shape, and bearing stiffeners, to CSA S16.

  12. Single angle in tension Pro report

    An equal-leg angle brace bolted by one leg, its tension and end moments combined to CSA S16 Cl. 13.9.

  13. Double angle in tension Pro report

    Two angles back to back as a tension brace, with the connection's eccentricity, to CSA S16.

  14. WT in tension Pro report

    A WT brace under tension and a moment compressing its stem, AISC 360-22 F9 resistance, CSA S16 Cl. 13.9.

  15. Tension and bending

    A W shape, HSS or channel under axial tension and strong-axis bending, CSA S16 Cl. 13.9.

calcsheet is a set of structural engineering calculations that show their working. Each page takes a handful of inputs, runs the calculation in Python, and prints every step of the derivation: the formula in symbols, the same formula with the numbers substituted, and the result with its unit.